高压洗车机的使用方法和保养 |
添加时间:2017/12/6 16:24:26 浏览次数: |
目前国内市场中高压洗车机的种类很多,按其使用功能的不同,可分为普通洗车机、高压洗车机、超高压洗车机及冷热水洗车机等。 At present, there are many kinds of high pressure car washing machines in the domestic market. According to their different functions, they can be divided into ordinary car washing machines, high pressure car washing machines, ultra-high pressure car washing machines, hot and cold water car washing machines, etc. 一、工作原理 1. Working principle 高压洗车机是利用工作泵内活塞的上下运动,而使吸进来的低压水变成高压水,从而变得较容易将车体表面的泥沙、灰尘、污垢等去掉。 The high pressure car washing machine uses the upper and lower movement of the piston in the working pump to make the suction low pressure water into high pressure water, which makes it easier to remove the sediment, dust and dirt on the surface of the car. 二、操作方法 Two. Operation method 开机前检查清洗机各部位螺钉、螺母是否有松动现象,向泵偏心轴箱内加入机油,油位加到油窗的一半为宜。 Before starting the machine, check the screw and nut of all parts of the cleaning machine to be loose, add oil to the eccentric axle box of the pump, and add half of the oil level to the oil window. (一) 开箱 (1) open the box 1.开箱后依据装箱单一一核对,检查确认所有机件是否齐全、完好 1. check and verify whether all the machines are complete and complete, according to a single check after packing. 2.使用说明书等文件资料要妥善保管 2. the documents, such as the use of the instructions, should be properly kept 3.拆除紧固螺丝,把机器从木箱中取出 3. remove the fastening screws and remove the machine from the wooden box (二) 加油 (two) refueling 1.取下罩壳,旋下泵体上面的油盖,注入2040号汽机油 1. remove the cover, spin the oil cover above the pump body, and injecting No. 2040 engine oil 2.注入600ml机油(油位加到油标线油窗的一半为宜) 2. injection of 600ml oil (half of oil level to oil line oil window) (三) 安装推把 (three) install push handle 1.从塑料袋取出推把,直接安装在机架上 1. remove the push handle from the plastic bag and install it directly on the rack. (四) 进、出水管安装 (four) installation of inlet and outlet pipes 1.将进水管的一端接头插入泵头下端的进水口并旋紧,另一端套于自来水龙头或置没于水池中; 1. one end joint of the inlet pipe is inserted into the inlet of the lower end of the pump head and tightened, the other end is placed on the tap water tap or not in the pool. 2.如选配混药功能,将混药管一端插在混药接头上,另一端浸入肥皂水中 2. if the selection of mixing, mixing tube end inserted in the mixing joint, the other end immersed in soapy water 3.将出水管的二端分别连接于泵头上端的出水口和喷枪进水口。 3. the two ends of the outlet pipe are connected to the outlet of the top of the pump head and the nozzle of the spray gun respectively. (五) 清洗作业 (five) cleaning operation 1.检查各连接处螺母螺钉是否有松动 1. check the loosening of nut screws at each connection 2.将机具移至作业地点并认真查看水源、电源是否符合安全要求。 2. move the equipment to the working place and carefully check whether the water source and the power supply are in conformity with the safety requirements. (注:电源要有良好接地且装有漏电保护器)。 (Note: the power supply should be well grounded and equipped with a leakage protector). 3.将调压旋钮逆时针旋松。 3. the pressure regulating knob counterclockwise unscrew. 4.先通水源,后通电源。压力调整需在泵内腔排尽空气,喷枪有水柱喷出后进行,逆时针旋转为压力下调,顺时针旋转为压力上调。压力调整必须在喷射状态下进行。工作压力最高不得超过额定压力 4. first pass the water, then pass the power. The pressure adjustment needs to exhaust air in the inner cavity of the pump, the spray gun has water column ejection, the counter clockwise rotation is down to the pressure, and the clockwise rotation is up to the pressure. Pressure adjustment must be carried out in the state of injection. The highest working pressure should not exceed the rated pressure 5.喷枪喷出的水柱有扇形和柱形两种形式,扇形水柱适用于大面积污垢的表面清洗,柱形水柱则适用于污垢严重的部位清洗。 5., the water column ejected by the spray gun has two forms: fan and column. The fan shaped water column is suitable for surface cleaning with large scale dirt. The cylindrical water column is suitable for cleaning the serious area. 6.旋转喷头护套即可变换水柱形式,变换形式须在闭枪状态下进行 The form of the water column can be changed by the 6. rotating nozzle sheath. The transformation form must be carried out in the state of the closed gun. (六) 保养 (six) maintenance 1、进水滤网的清洗经常将进水滤网取下清洗、去除滤网上的杂物,并用软刷轻轻洗净,以社绝滤网堵塞,吸水不足造成压力下降。 1, the cleaning of inlet filter net often removes and filters the waste water filter screen, removes the debris on the filter net, and gently rinses it with soft brush, so as to stop the pressure drop due to the blockage of the filter screen and insufficient water absorption. 2.曲轴箱的清洗新机在使用20小时左右必须更换机油。步骤:松开放油螺钉,将机具倾斜,排尽泵内机油,随后倒入少量柴油,清洗泵内腔,重复数次,直到放出的柴油清洁为止。然后重新注入规定的机油,以后每隔100小时更换机油一次,这样对延长机具使用寿命至关重要。 2. the new machine for the cleaning of the crankcase must replace the oil for about 20 hours. Step: loosen the oil drain screw, tilt the machine, drain the oil in the pump, then pour in a small amount of diesel oil, clean the pump cavity, repeat it several times until the released diesel is clean. Then the required oil is re injected, and the oil is replaced every 100 hours, which is essential to prolong the service life of the machine. 定期检查: Regular examination: 1、箱体内机油干净、不发白 1. The oil in the box is clean and not white 2、箱体所有接合处不得有漏油,确保油位在油窗一半处为宜 2. No oil leakage is allowed in all joints of the box, so as to ensure that the oil level is suitable for half of the oil window. 3、三个月后检查出水接头里面的单向阀,磨损严重更换; After 3 and three months, check the unidirectional valve inside the outlet joint, and the wear is changed seriously. 4、检查进水过滤网是否损坏,损坏更换; 4. Check whether the inlet filter net is damaged or damaged and replaced. 5、检查喷枪关枪是否漏水、如漏水、修复或更换喷枪 5. Check whether the gun is leaking, such as water leakage, repair or replacement of a spray gun. 三、注意事项 Three. Precautions 1、供水一定要干净,无杂质; 1, the water supply must be clean, no impurities; 2、进水管要安装过滤网,以免杂质进入泵内; 2, the inlet pipe should be installed filter net, so as to avoid impurities entering the pump; 3、洗车停顿或结束时,一定要及时关闭电源,以免让工作泵空转,此时泵内 压力极高,很容易加速工作泵内运动部件的磨损。 3, when the car stops or ends, it is necessary to turn off the power in time, so as not to make the working pump idle. At this time, the pressure inside the pump is very high, so it is easy to accelerate the wear of moving parts in the working pump. |
上一页 自助洗车机,洗车行业的印钞机 |
下一页 家用便携洗车机,让爱车改头换面! |
Copyright © 技术支持:遨游网络